• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Repair - Simple Fixes You Can Do in a Few Easy Steps

It's easy to assume that a door can't be repaired however, there are many easy fixes that can make a huge impact. Let's start by the shimming.

To shim a room, open the door and press it firmly against the frame. Use a block plane or an jack plane to remove tiny amounts of wood around the binding points.

The Frame

The door frame is a crucial element of your home. It provides security, prevents water damage, and gives your home an attractive appearance. It is prone to damage. Door frames can be damaged by bad weather or burglaries, as well as regular use. If they do, it can cause large gaps, weak latching, and a shabby appearance. Fortunately, fixing your door frame is a relatively simple task that can be completed in a few steps.

The first step is to take the trim, or molding, from around your door's opening. You can use a hammer, the chisel or a power saw to take off the trim. After the trim is removed, make a note of the measurements to replace it after the repair.

You will then need to look over any damaged or rotten areas of the door frame. If there are any rotten areas, you will need to buy and install replacement pieces of wood. These are usually available at your local hardware shop and should be constructed of materials that match the rest of your door frame. Avoid pressure-treated wood since it can be twisted and warped over time.

After replacing any rotten components of the frame you will have to secure it. One way to accomplish this is using an shim. It is basically a piece of wood that is placed between the frame and the wall. The shim provides extra support for the frame and prevents it from moving.

After you have replaced any shims, it's recommended to seal around the door frame and sill. This will keep water damage from occurring and shield the frame from pests.

You will then need to install your trim again on the door frame. If you are lucky, Double Glazing Repairs your previous trim may be in good condition and you can simply nail it back into its place. If not, you may have to buy new trim and follow the same procedure.

The Threshold

A threshold is a strip of wood that is used to cover and insulate the gap between the door and the floor. It also prevents water and snow from collecting in the entranceway. A properly installed threshold is not just a vital part of your door, but it's also a beautiful accent to enhance the appearance of your home's exterior. If your threshold is scuffed, worn or damaged, it's time to replace it. Installing a new threshold is not as simple as simply sliding it under the casing before nailing it to the frame it must be held up by wood strips called shims. They are inserted between the frame's two jambs.

To remove the threshold first, cut it away from the edges of the door frame using a circular saw (use a carbide blade, if possible). If you can take out the sub sill - the frame part which runs below the threshold. Replace it if it's damaged at the same time as you replace the threshold.

Before cutting the threshold to the proper size, use a carpenter's square to draw the lines of layout on it, noting right angles for notches that can be positioned around the jambs. You can also buy pre-cut thresholds that match the width of your doorway at a home center.

Install the shims evenly, and ensure that you space them. If necessary, you can change the thickness of the shims. But they shouldn't be wider than 1 1/2 inches. It could require a bit of trial and error to make the threshold snug but still able to move freely.

Close the door and observe how it opens and shuts. There shouldn't be any daylight under the door and the sweep at the bottom of the door should rap against the top of the threshold.

If the threshold is a good fit, but requires a bit more support, place some construction adhesive on the shims, then press them into place beneath the threshold. Repeat the process with more shims until you have a tight fit that can withstand weight.

The Hinges

Many hinges on doors rust or deteriorate over time, making it harder to close the door. If this happens, it's essential to repair the hinge in order that the door is closed and secured properly. When replacing the hinge, make sure you choose one that is similar in size and shape. You should also make sure that the hinge is located in the mortise.

The first step is to check the hinge for any looseness. If the hinge isn't tight, it could be rubbing against the strike plate, and will bind to the frame. Check for paint scratches or indents on the frame to indicate the location where the hinge is rubs. If the issue is the hinge isn't securing enough then use a screwdriver tighten it. If the hinge is still too loose, you might have to replace it. You can try putting an shim between the door frame and the hinge.

If the problem is that the knuckles of the hinge (the cylinders that the hinge pin is fitted) are bent in a way, you'll need to straighten them to point towards the jamb on the latch. You can do this by gently bent the knuckles with a pair of large tongue-and-groove-pliers or an adjustable wrench, double glazing repairs (gorod-lugansk.com) however it is best to work on just one individual knuckle at a given time to ensure that you don't accidentally bend the hinge leaf out of its mortise.

You may also find that the hinges on your doors are loose because the screws that hold them in place have stripped. If this is the case you can replace the screws to give them more grip on the hinges.

If the hinge isn't damaged and the screw holes are in good condition, you can use a syringe to inject carpenter's glue into the mortise and joint of the hinge. Then screw the hinge back into place and secure it with an screwdriver or drill. Mark the location of the pilot holes in the door and frame before installing new hinges. This will help to make sure that the screws are in the exact same spot as the old ones.

The Hardware

Most people don't give much thought to door knobs, locks or levers until they stop functioning properly. Most of these components are easily repairable. It is usually a simple choice of choosing the right piece that matches the style and design of your home, and then installing it. It's a good idea, especially for exterior doors, to add weather-stripping.

If you have a door which is difficult to open, you may be able solve the problem by lubricating the lock assembly. There are many kinds of locks, handles, and hinges are susceptible to sticking when their wear surfaces become dry or dirty. Keeping these parts clean and lubricated is a cost-effective method of ensuring they function properly.

The most frequent issues with door hardware are loose or broken handle screw, a lock which won't turn on its own when you insert hinges that squeak or stick. In the majority of instances you can tighten the screws or replace them completely. In some instances it is better to remove the handle or lock from the door and then sand the spindle, lock cylinder bore hole and escutcheon holes to make sure they're clean before installing the new hardware.

For doors that are difficult to close, you may need to lubricate the locking mechanism using penetrating oil. You can clean and reinstall hinge pins using longer screws to fix doors that are squeaky.

If you need to replace a handle, lock, or hinge, be sure to choose a model that is compatible with the current hole size on your door and jamb. You'll usually find this information in the packaging or on the website of the manufacturer. For instance, doorknobs and levers need holes that have at a certain spread (the distance from the center of the hole in the lock to the knob). Check the backset to see whether the replacement is compatible with.